Skip to main content

AI Story · 3D Estimate AI

The rules do the estimate. The AI takes what they can’t.

3D Estimate AI prices steel from the model your detailers work in. Rules and the AISC engine do most of the work; AI is called only for what they leave open, such as an unclear connection, a step with no quantity or a second look at the finished estimate. Every answer comes back as a proposal, or carries a flag that says AI.

  1. Rules settle most joints
  2. AI proposes the unclear ones
  3. Sure answers applied, rest queued
  4. You accept or reject them

Where AI works

7 places in 3D Estimate AI use AI. In every one, a person has the last word.

  1. Auto-Detect

    Estimate › Model View › Auto-Detect

    Reads
    The connection pairs in the model that the rules, the Connection Table and the AISC engine could not settle, such as a framing condition that is empty or unclear.
    AI proposes
    A framing condition for each of those pairs, with how confident it is.
    You decide
    Only answers above a confidence threshold you set are applied. Everything below it waits in the Human Review Queue for you to accept or reject.
  2. Classify with AI

    Estimate › Model View › Classify with AI

    Reads
    Modelled connection pairs that the rules pass could not label.
    AI proposes
    A connection label for each of them.
    You decide
    The label is a suggestion until a person accepts it. It never sets a member’s review status or its connection type on its own.
  3. AI Fill

    Setup › Connection Table › AI Fill

    Reads
    The rows of your Connection Table still empty after the AISC rules have run.
    AI proposes
    Bolt, weld and plate values for those rows.
    You decide
    It asks before it starts, fills only empty fields, never replaces a value you entered, and every filled row stays editable.
  4. AI-refined quantities

    Inside the estimate run › AI column in the member report

    Reads
    The fabrication steps the cost engine could not price from its own data.
    AI proposes
    A quantity for each of those steps, project adjustment factors, and the members that look out of line.
    You decide
    This is the one AI step that runs without a click, so every value it fills is flagged AI Refined in the report and the 3D view, for you to check. If the AI is unavailable, the estimate uses the engine’s own values.
  5. AI Estimator

    Reports › AI Estimator

    Reads
    The finished fabrication or erection estimate, after a rules pass has checked it.
    AI proposes
    The questions and findings a senior estimator would raise, and sometimes a correction.
    You decide
    Findings are for you to acknowledge, and a correction is applied only by a person with permission, who can undo it. Your team rates the findings, and if it disagrees too often, they are marked as possible and then switched off.
  6. Erection planning

    Erection Planning › Compute duration, Explain, Ask AI where they go

    Reads
    The erection plan the rules computed: zones, cranes, sequence and workflows, with the members they could not place.
    AI proposes
    Days for each zone, an explanation of the crane ranking, a place in the sequence for the members left over, and a short critique of the plan.
    You decide
    Each one runs only when you click it, and the rules check every answer again. Durations and suggestions are stored as proposed, and the estimate reads only the ones you accept.
  7. Ask AI

    Header › Ask AI

    Reads
    Your question in plain language, answered from this project’s live estimate and model data, or from the module’s guides for a how-do-I question.
    AI proposes
    An answer, or an edit such as a member mark, shown as Before and After.
    You decide
    Nothing changes until you click Apply, and you can cancel or undo it. A guide answer cites the guide it came from and says so when the guides do not cover it.

What isn’t AI

Plain software that gives the same answer every time. We don’t call it AI.

  • Cost engine pricing and roll-ups
  • AISC connection design
  • Rule-based connection matching
  • Member classification and framing detection
  • Grids derived from column positions
  • Length corrections
  • Profile and grade fixes from the AISC catalog
  • The suggested erection plan
  • IFC and Revit import, revision compare and exports